MJ Leckie Carpentry
Back to Blog
Decks 16 November 2026

[AI Draft] The 1-Metre Deck Rule in NSW: Council Approvals, Balustrades, and Height Limits Explained

If you are planning to build a deck on the Northern Beaches, there is one magic number you need to keep in mind: 1 metre.

In New South Wales, the 1-metre height mark is the critical threshold that dictates whether you can build without council approval, whether you are legally required to install a balustrade, and even how thick your structural timber needs to be.

However, many homeowners confuse the planning rules (council approval) with the building rules (safety and structure). While they both use 1 metre as a benchmark, they measure it differently and apply it for entirely different reasons.

As licensed carpenters (NSW Lic 353438C), we build decks across Sydney's Northern Beaches every week. In this guide, we will break down exactly what the 1-metre rule means for your outdoor project, referencing the current National Construction Code (NCC 2022) and NSW planning legislation.

The Homeowner Question

"I want to build a deck in my backyard that sits about a metre off the ground to match my back door. Do I need council approval, and do I have to install a handrail?"

The short answer: If your deck is exactly 1 metre above the existing ground level, you might avoid council approval (if you meet other strict criteria), but you will absolutely need to consider structural upgrades. If it is 1000mm or more above the surface below, a compliant balustrade is mandatory. Let's look at the specific rules.

1. The 1-Metre Rule for Council Approval (Exempt Development)

In NSW, you don't always need to submit a Development Application (DA) to build a deck. Under the State Environmental Planning Policy (Exempt and Complying Development Codes) 2008 (often called the Codes SEPP), you can build a deck as "Exempt Development" if it meets a strict list of criteria.

According to Part 2, Division 1, Subdivision 6 of the Codes SEPP, your deck must have a floor height of not more than 1 metre above existing ground level.

If your deck is 1.1 metres off the ground, it is no longer exempt. You will need to apply for a Complying Development Certificate (CDC) or a full DA.

But height isn't the only rule. To be exempt, your deck must also:

  • Have an area of not more than 25m².
  • Be set back at least 900mm from the lot boundary (or 5m in rural zones like RU1 or R5).
  • Not extend beyond the building line of any road frontage.
  • Not have an enclosing wall higher than 1.4m.

Note for Northern Beaches locals: If your property is in a bushfire prone area (BAL-rated) and the deck is within 5m of your house, you must use non-combustible materials. If you are in a heritage conservation area, exemptions are heavily restricted.

2. The 1-Metre Rule for Balustrades (Safety)

While the planning laws care about how high your deck is compared to the natural ground, the National Construction Code (NCC) cares about how far you could fall.

Under the NCC 2022 Housing Provisions (Part 11.3), a continuous balustrade or barrier is mandatory if the potential fall from the deck surface to the surface beneath is 1000mm or more.

If your deck requires a balustrade, it must meet strict safety standards:

  • Height: The balustrade must be at least 1000mm high above the finished deck floor.
  • Gaps: Any openings in the balustrade must not permit a 125mm sphere to pass through (this is to prevent young children from slipping through).
  • Strength: It must be structurally adequate to resist the loads specified in AS/NZS 1170.1 (Structural design actions).

If your deck is on a sloping block and the fall exceeds 4 metres, additional rules apply to prevent climbing. Any horizontal elements between 150mm and 760mm above the floor must not facilitate climbing (often referred to as the non-climbable zone).

What the Code Actually Says

How is the 1 metre measured? This is where people get caught out. For Exempt Development (council approval), the height is measured from the existing ground level (the natural state of the ground before you started digging). For Balustrades (NCC safety), the height is measured from the finished deck surface to the surface beneath (which could be a concrete path, a garden bed, or excavated ground). You could have a deck that is 900mm above the natural ground (exempt from council approval), but because you excavated a garden bed below it, the actual fall is 1100mm—meaning a balustrade is legally required.

3. The 1-Metre Rule for Structural Framing

The height of your deck also dictates how we build the subfloor. The Australian Standard for residential timber framing (AS 1684.2) has different span tables depending on how high the deck is.

  • Decks 1000mm or less above ground: We use Table 5 (Floor bearer tables).
  • Decks greater than 1000mm above ground: We must use Table 49.

Why the difference? Elevated decks are subjected to different forces, and a failure at a higher elevation carries a much higher risk of injury. Elevated decks must be designed to handle a live load of 2.0 kPa (kilonewtons per square metre) as per AS/NZS 1170.1. This often means using thicker bearers and joists, or spacing your posts closer together to prevent the deck from feeling "bouncy."

Furthermore, if we are attaching the deck to your house using a waling plate (ledger), NCC 2022 Part H1D11 states that this method is only deemed-to-satisfy if the deck height is not more than 3 metres, does not cantilever off the external wall, and the total imposed load does not exceed 2 kPa.

4. Termite Protection and Timber Treatment

Regardless of whether your deck is 200mm or 2000mm off the ground, it must comply with AS 3660.1 for termite management.

If your deck is attached to your home, it cannot bridge the existing termite barrier. We must ensure there is a clear inspection zone. For the timber itself, any posts set into the ground must be treated to at least H4 (suitable for in-ground use) as per AS/NZS 1604. Bearers and joists above ground must be at least H3 treated.

Low-level decks (under 400mm) present a unique challenge because they restrict subfloor ventilation and make termite inspections difficult. In these cases, we often recommend composite decking over a steel frame, or ensuring adequate drainage and airflow to prevent moisture buildup and timber rot.

Doing It Right the First Time

Building a deck on the Northern Beaches isn't just about nailing some boards together. It requires a deep understanding of the Codes SEPP for planning exemptions, the NCC for safety, and Australian Standards for structural integrity.

Trying to skirt the 1-metre rule by building a deck at 999mm might seem like a clever way to save money on a balustrade, but if the ground settles or washes away, you could find yourself with a non-compliant, unsafe structure that causes major headaches when you try to sell your home.

Ready to build a deck that looks incredible and complies with every NSW regulation? At MJ Leckie Carpentry, we handle everything from the structural framing to the final oiling, ensuring your outdoor space is safe, legal, and built to last. Contact us today for a free, no-obligation quote on your Northern Beaches deck project.

"Let us create a relaxing space at your place"

MJ Leckie Carpentry

MJ Leckie Carpentry

Licensed Carpenter — NSW Lic 353438C · Northern Beaches, Sydney

0482 088 410

Ready to start a similar project?

Get a free site measure and custom quote.

Ready to Start Your Outdoor Project?

Get a free written quote. No obligation, no hard sell.

We use essential cookies for site functionality, and analytics cookies to understand how you use our site. Declining analytics won't affect site functionality. Privacy Policy